How to Use

Easy steps on how to use each and every vaporizer.

← Older posts

3 Easy Steps on How to Use the Essential Vaaapp Vaporizer

Step 1: Open the Vaaapp glass vial

As with the Magic-Flight, this vape only needs 3 steps to use. First unscrew the glass vial from the top of the vaporizer. Be extra careful when removing the vial though because it can be kind of easy to break. When I say easy to break I really really mean it. Whether it be the glass breaking in the threading of the vial or it just completely shattering. It’s fragility is amplified when it is being heated up also.

IMAG0390 300x200 3 Easy Steps on How to Use the Essential Vaaapp Vaporizer

Step 2: Pack the Vaaapp

Next place ground up herb into the glass vial, letting it settle at the bottom of the Vaaapp. Before you light under the herb though you will want to heat the upper part of the glass vial for about 6-8 seconds, before moving down to heat under the herb like shown below:

Vaaapp Light 200x300 3 Easy Steps on How to Use the Essential Vaaapp Vaporizer

Step 3: Begin use of the Vaaapp

Don’t pull right away or while lighting, wait until you see vapor fill the glass, stop lighting and pull through the mouthpiece and clear the vapor from the tube. Discard used herb and repeat the previous steps.

vaaap 282x300 3 Easy Steps on How to Use the Essential Vaaapp Vaporizer

Tip: When transporting this vape always use the carrying case. The glass vial is very easy to break.

If you haven’t read the review of the Essential Vaaapp I find it essential that you do. You can find it here. Wanna see how much this vaporizer costs? Compare prices and vendors for the Vaaapp.

Posted in Articles, How to Use | Tagged , , , , | Leave a comment

5 Easy Steps on How to Use the Aroma Deluxe Vaporizer

AROMA 5 Easy Steps on How to Use the Aroma Deluxe Vaporizer

Step 1: Turn on the Aroma Deluxe

Adjust the temperature knob to the second green block above the knob, as this is the recommended setting. While smoking you can change it around to find what temperature best suits you though. The vape only takes about 2 minutes to heat up like I said.

Step 2: Pack the Aroma Deluxe

Grind up your herb extra fine so you don’t end up wasting any. Place the herb in the bowl piece of the Aroma Deluxe and don’t fill it up more than a 1/3 of the way.

Step 3: Attach the Aroma Deluxe whip

Place the bowl end of the whip onto the ceramic heating element. It should fit perfectly on there and feel set. This will start the vaporization process.

Step 4: Begin use of the Aroma Deluxe

Gently pull for about 10 seconds giving the vapor a chance to build up. After that start pulling harder and you should get a decent amount of vapor. Also adjust the temperature while smoking if you find the vapor to be too harsh or not good tasting.

Step 5: Refill the Aroma Deluxe

When you’re done simply remove the whip from the Aroma Deluxe ceramic heating element and discard the left over herb. Then replace it with more herb, finely ground up, and repeat the previous steps until you’re done the session.

If you haven’t read the review of the Aroma Deluxe well color me disappointed. You can find it here. Ready to see the best places you can buy this vaporizer? Compare prices and vendors for the Aroma Deluxe.

Posted in Articles, How to Use | Tagged , , , | Leave a comment

5 Easy Steps on How to Use the Vaporfection Novus

Vaporfection Novus 5 Easy Steps on How to Use the Vaporfection Novus

Step 1: Turn on the Vaporfection Novus

To start you’ll want to plug in the power cord to the back of the vape and switch it on. Also be sure that the vape is not in standby mode, which you will know by the green LED light being on.

Step 2: Heat up the Vaporfection Novus

The heat up on the Novus is pretty short, around 2 minutes generally. Simply set your temperature you wish to vaporize at on the LED read out (and remember it is set it and forget it) and wait for it to heat up. You’ll know it’s ready when you hear the fan kick on.

Step 3: Pack the Vaporfection Novus

Now above the screen in the whip you spread your herb evenly over it. As always make sure you don’t pack it completely full and to maximize the surface area so you aren’t wasting any herb.

Step 4: Begin use of the Vaporfection Novus

Once you put the herb packed end of the whip onto the heating element it will begin to vaporize. Next just pull from the mouthpiece end of the vapor whip and take a couple short quick pulls to get it going.

Step 5: Refill the Vaporfection Novus

When you are done you can either refill the vapor whip or simply turn the vape off. Also if you want you can leave the cape on since it has an auto shut off feature. once it reaches room temperature it will shut itself off.

If you have yet to read the Vaporfection Novus review it isn’t hard to find. You can read it here. Thinking about picking up this vape? Compare prices and vendors for the Vaporfection Novus first!

Posted in Articles, How to Use | Tagged , , , | Leave a comment

3 Easy Steps on How to Use the Incredibowl Mini m420

Step 1: Pack the Incredibowl Mini m420

First remove the glass bowl from the Bowl Armor. Once removed pack the bowl as tight as you can either leaving your material whole or grinding it. I tend to grind my material because I believe it works better even when you aren’t vaporizing. Once the bowl is packed insert the glass bowl back into the Bowl Armor.

Step 2: Light the Incredibowl Mini m420

Now that the bowl is packed hold the lighter flame in front of the bowl, not touching it, and pull on the expansion chamber. This will draw the flame to your material and light it. You should instantly see the chamber fill with smoke.

Step 3: Clear the Incredibowl Mini m420

When the chamber appears to be full with the amount of smoke you want pull on the Bowl Armor. This will let fresh air rush in and clear the expansion chamber. If you found the pull to be too big simply pull the Bowl Armor faster for less smoke.

Check out the in depth Incredibowl Mini m420 review if you haven’t already. Compare prices and vendors for the Incredibowl Mini m420 before you buy.

Posted in Articles, How to Use | Tagged , , , , | Leave a comment

3 Easy Steps on how to Use the Fumo Pipe

Step 1: Pack the Fumo Pipe

The bowl of the Fumo Pipe is located right on top, so simply drop your material into the bowl, either ground up or not. You don’t have to particularly pack the bowl super tight since the bowl is facing upwards, but you can if you want to.

Step 2: Light the Fumo Pipe

Place your lighter over the bowl and gently pull from the expansion chamber to begin lighting your material. You will quickly see the chamber fill with smoke and from here you just have to gauge what size pull you would like. Obviously the thicker the smoke the bigger the pull.

Step 3: Clear the Fumo Pipe

When you have determined you have the desired amount of smoke in the chamber simply press down the button that is on top of the Fumo Pipe located right in front of the bowl. This will allow fresh air to rush in and clear the chamber.

Take a peep at our full Fumo Pipe review. Compare prices and vendors before purchasing the Fumo Pipe.

Posted in Articles, How to Use | Tagged , , | Leave a comment

3 Easy Steps on How to Use the Incredibowl i420

Step 1: Pack the Incredibowl i420

First remove the glass bowl from the Incredibowl’s Bowl Armor. Once it is removed you have to pack the bowl very tight. You can do this by leaving your material whole or also grinding it. Either way will work fine but I generally grind up my material anyway. Once it is packed nice and tight put the glass bowl back in the Bowl Armor.

Step 2: Light the Incredibowl i420

While holding the Incredibowl parallel to the ground place the open end of the expansion chamber to your mouth, use a standard lighter to light your material and begin pulling from the expansion chamber. You should see smoke start to build up instantly.

Step 3: Clear the Incredibowl i420

Once your desired amount of smoke is in the expansion chamber simply pull on the Bowl Armor to let fresh air in and clear the chamber. If you find the smoke to be a little too harsh it just means that you may have taken too big of a pull. Simply cut down on the time you wait before pulling the Bowl Armor and clearing the chamber.

Take a look at our full Incredibowl i420 Deluxe review and also compare prices and vendors for the Incredibowl i420 and Incredibowl i420 Deluxe before you buy.

Posted in Articles, How to Use | Tagged , , , | Leave a comment

3 Easy Steps on How to Use the Wispr

Step 1: Turn on the Wispr

To turn the Wispr on simply pull down once on the trigger located on the side. When you do, you will hear it start to vent butane, this is when you pull the trigger again which will start the heating process. You should see the LED light indicator on the Wispr light up as well.

Step 2: Pack the Wispr

Remove the mouthpiece from the top of the Wispr, revealing the herb chamber. Now drop your ground up material into the herb chamber and put the mouthpiece back on top.

Step 3: Begin use of the Wispr

After placing the mouthpiece back on top of the Wispr give it about 30 seconds before you take a pull. This will give it some time to build up some vapor. You want to take slow and long pulls rather than quick and heavy pulls because the vapor can be very hot when you pull too fast.

If you have yet to read the Wispr vaporizer review you should do so to get a better idea of its improvements over the Iolite. Compare prices and vendors for the Wispr vaporizer.

Posted in Articles, How to Use | Tagged , , | Leave a comment

5 Easy Steps on How to Use the Arizer Solo

Step 1: Turn on the Arizer Solo

Turn the Arizer Solo on by simply pressing and holding both the up and down arrows on the front of the vape. Once you hear a beep you will know it is turned on and you can let go of the buttons. The second it turns on it will begin to heat up to a default temperature of around 100 degrees Fahrenheit, so once you pick a heat level the heating process will be faster.

Step 2: Pick a heat level on the Arizer Solo

Next you have to decide which heat level will best suit you, or at least where you want to start. Here is a list of the heat levels in Fahrenheit and Celsius to better help you choose:

  • Level 1: 50 C – 122 F
  • Level 2: 185 C – 365 F
  • Level 3: 190 C – 374 F
  • Level 4: 195 C – 383 F
  • Level 5: 200 C – 392 F
  • Level 6: 205 C – 401 F
  • Level 7: 210 C – 410 F

Personally I would stop at heat level 3. From there you will be able to tell if you want to make it hotter for a thicker vapor or cooler. Lastly, before setting the heat level you want make sure you remove the mouthpiece so that it doesn’t heat up with the Solo.

Step 3: Pack the Arizer Solo

Now that the Arizer Solo has reached your desire heat level you want to take the glass mouthpiece and pack the bowl end with your ground up material.

Now flip the Arizer Solo unit upside down so the opening with the heating element is facing the floor. Take the bowl end of the glass mouthpiece and insert it into the hole where the ehating element is and flip it back right side up.

Step 4: Begin use of the Arizer Solo

Don’t wait too long to take your first pull once connecting the mouthpiece to the heating element because I found that it can affect the taste. When you pull take long slow pulls, rather than really strong pulls because since the Solo does not use a screen you can experience some of your material sneaking through those two little holes in the mouthpiece.

Step 5: Clean out the Arizer Solo

When you are done, you should notice by taste and the vapor thinning out, remove the glass mouthpiece by grabbing towards the top and not the bottom since it will be very hot. Dump the used material by blowing through the mouth end of the mouthpiece and then make sure that no material is left over inside the opening where the heating element is. Keeping up on this will save you a headache down the line because it will make it hard for any material to stick and “cake” onto the heating element.

Head over to our in depth Arizer Solo portable herbal vaporizer review to get the full scoop on this vape. Want to see how much this vape will cost you? Compare prices and vendors for the Arizer Solo.

Posted in Articles, How to Use | Tagged , , | Leave a comment

5 Easy Steps on How to Use the Vapolution 2.0

Step 1: Turn on the Vapolution 2.0

Take your Vapolution power adapter and connect it to the back of the vape, then plug that into the wall. Now flip the green switch up to the on position and you should see the switch light up. This means the vape is on and ready to be heated up.

Vapolution 20 dial 5 Easy Steps on How to Use the Vapolution 2.0Step 2: Heat up the Vapolution 2.0

Now that the Vapolution is turned on you want to adjust the temperature dial so it can begin heating up. The best place to start in my opinion is at 12 o’clock. This is going to give you a nice temp to start at so you can then further adjust it either higher for thicker vapor or lower for a thinner and cooler vapor. Just don’t go too low or too high because then you will either not have it hot enough to vaporize or so hot it will burn your material. The chart to the right is a perfect example.

Step 3: Pack the Vapolution 2.0 whip

About 1 inch from the end of the bowl end of the whip is a small “dimple” that works like a screen for the whip. This is where you want to pack your material. Be sure not to grind your material too fine because then it can slip past that “dimple” I just mentioned. Vapolution actually recommends you use “pods” of your material rather than grinding it at all. I still feel like grinding it at least a little bit helps get the most out of your material.

Step 4: Begin use of the Vapolution 2.0

Now that the bowl end of the whip is all packed up you want to slip the retaining washer about 3 inches from the “dimple” where your material is packed. After that simply drop the loaded bowl end into the top of the Vapolution. Give it about 10 seconds before you start to pull, this gives the some time to build some vapor.

Step 5: Clear out the Vapolution 2.0

Once you are finished remove the bowl end of the whip from the Vapolution and blow into the mouthpiece end of the whip. This will push the material out of the bowl so you can pack it again or put it away.

Posted in Articles, How to Use | Tagged , , , | Leave a comment

5 Easy Steps on How to Use the VripTech Heat Wand 3.0

Step 1: Prepare the VripTech Heat Wand

Before you do anything you are going to have to get your full VripTech Heat Wand setup all ready to go. First have your upper intake and lower bowl constructed and make sure they fit into your water tool correctly. Your glass heat cover should have come attached to your Heat Wand but if not slip it on and screw it in place and be sure to use the rubber circle and washer to stop the screw from making contact with the glass.

Step 2: Heat Up the VripTech Heat Wand

After you plug in the Heat Wand turn the dial that has a circular red arrow clockwise until it is all the way up. Next place the Heat Wand tip down into the glass stand. If you did not purchase the glass stand (highly recommended) then a tall mug should work fine.

Step 3: Pack the VripTech Heat Wand

When you remove the upper intake you will reveal the herb chamber where your material goes. Place a small amount of material over the screen and put the upper intake back on. Make sure when packing the herb chamber you don’t put a lot in. The herb chamber is that small for a reason, the VripTech Heat Wand 3.0 gets pretty much every last bit out of your material, so over packing it is not necessary. The chamber is deceptively small, but after one pack you’ll know it is doing its job with the small amount of material it requires. Finally put the lower bowl and upper intake back into the stem of your water tool.

Step 4: Begin Use of the VripTech Heat Wand

First remove the Heat Wand from the glass stand, or tall mug if you used that instead, and move the heat dial down a little from its highest setting than you had it at while heating up. That is just to start, you may want to increase it back to its max setting like I do, it is a matter of preference and you will know which you prefer after a couple tries. Place the rubber tip of the Heat Wand into the large open end of the upper intake and hold it there for about 30 seconds to a minute. After waiting about a minute pull from your water tool. Exhale the first small pull you get without removing the lower bowl from the water tool, this first pull kind of gets the Heat Wand ready for the following pull by building up some vapor. Now take your next pull and make this one as big as you want. Once you have the desired amount of vapor in there just pull the Heat Wand up and it should take the upper intake and lower bowl with it as well and allow fresh air in, clearing the water tool.

Step 5: Stir or Repack the VripTech Heat Wand

After you have taken one or two good pulls from the VripTech Heat Wand 3.0 remove the upper intake exposing the herb chamber and give your material a light stir. This will get you at least one or two more good pulls. When you are done remove both the upper intake and the lower bowl. Empty out the used material and repack it if necessary. Turn the Heat Wand’s heat dial all the way down and place it back in the glass stand and unplug the Heat Wand from the wall.

Be sure to read the VripTech Heat Wand 3.0 vaporizer review if you haven’t yet. Want to see how much this awesome vape will run you? Compare prices and vendors for the VripTech Heat Wand 3.0

Posted in Articles, How to Use | Tagged , , | Leave a comment

3 Easy Steps on How to Use the Vape-Or-Smoke

VapeOrSmoke 3 Easy Steps on How to Use the Vape Or Smoke

Step 1: Adjust the flame level of the Vape-Or-Smoke

First you have to decide whether you are going to smoke or vaporize with the unit. If you are going to smoke with it you can leave the flame level a little higher, if vaporizing lower it almost as much as you can. To get to the flame adjuster you simply slip the cover off of the Vape-Or-Smoke and look at the bottom, you’ll see a small knob you can turn with a screwdriver or use your nail.

Step 2: Pack the Vape-Or-Smoke

Next you want to push up the bowl piece, it will lift the entire inside of the unit revealing the herb chamber. Simply pack the herb chamber with your desired amount of material and then push the chamber back down into the unit.

Step 3: Begin use of the Vape-Or-Smoke

Pop out the mouthpiece using the top of it and put your mouth on the mouthpiece. Now while pulling down on the unit and pushing the mouthpiece up inhale to get the flame ignited. If you are smoking you can take long drawn out hits, but if you are vaporizing you want to take quick and small pulls. Taking long hits even with the flame turned down can still result in combustion.

If you need to take a look at what this unit has to offer check out our Vape-Or-Smoke review. You can find it here. Before you order the Vape-Or-Smoke compare prices and vendors.

Posted in Articles, How to Use | Tagged , , , , , , | Leave a comment

3 Easy Steps on How to Use the Phedor Electric Lighter

Phedor 3 Easy Steps on How to Use the Phedor Electric Lighter

Step 1: Plug in the Phedor

Attach the power cord that comes with the Phedor to the back of the unit and plug it in. Give it about 45 second to a minute to heat up, you’ll know it’s ready when the heating element is glowing orange.

Step 2: Use the Phedor to vaporize or smoke

Now take the heating element part of the Phedor and very carefully hover it over your blend. If you don’t wish to vaporize, simply touch the heating element to your blend to begin combustion.

Step 3: Power down the Phedor

When you are done you’ll want to unplug the Phedor and let it rest and cool down before storing it anywhere. If you make the mistake of placing it somewhere while it is still hot you’ll probably end up burning your place down.

If you haven’t read the review of the Phedor Electric Lighter you can find it here. Thinking about ordering this electric lighter? Compare prices and vendors for the Phedor before you do.

Posted in Articles, How to Use | Tagged , , | Leave a comment

5 Easy Steps on How to Use the VaporBox Vaporizer

VaporBox VS 5 Easy Steps on How to Use the VaporBox Vaporizer

Step 1: Turn on the VaporBox

Turn on the VaporBox and set it to the temperature you want to vaporize at. I found that going no lower than 325 degrees and no higher than 345 degrees Fahrenheit worked best.

Step 2: Pack the VaporBox

Grind up your herb finely like usual and pack it into the bowl piece at the end of the vapor whip. Of course don’t pack it too much because you will just be wasting herb at that point.

Step 3: Place the bowl piece onto the heating element of the VaporBox

Take the bowl piece that you just packed with herb and place it over the center cut hole of the ceramic heating element. This will start the vaporizing process.

Step 4: Begin use of the VaporBox

Now that the bowl piece is placed over the heating element you will want to take the glass mouthpiece end of the vapor whip and start to pull from the whip.

Step 5: Refill the VaporBox

When you start to get that kind of burnt popcorn flavor it is time to ditch the herb and repack the vape. Remove the bowl piece from the heating element and blow out the mouthpiece to fully clear the whop of herb.

Before making a final decision, read our VaporBox Vaporizer review. If you aren’t sure where to purchase a VaporBox Vaporizer you should compare prices and vendors for it.

Posted in Articles, How to Use | Tagged , , | Leave a comment

5 Easy Steps on How to Use the Purple-Days Vaporizer

Purple Days 5 Easy Steps on How to Use the Purple Days Vaporizer

Step 1: Turn on the Purple-Days Vaporizer

First you want to plug in the Purple-Days, simply put the A/C adapter plug in the back of the vape and plug the other end into the wall.

Step 2: Heat up the Purple-Days Vaporizer

You have to give the Purple-Days about 30 to 45 minutes to heat up the first time, but you can leave it on after that for as long as you like just like the Myrtlezap. Now you can fill one of the short nylon stems with herb.

Step 3: Pack the Purple-Days Vaporizer

Take one of the nylon stems provided and place the herb bowl end over your ground up herb. Now pull the herb into the herb chamber by gently pulling from the mouthpiece end. Once you see it filled with herb take the small packing tool they give you and lightly pack the herb into the chamber. Just don’t push too hard. Also if you like you can pack it by hand instead of sucking it into the herb chamber, both ways work fine.

Step 4: Attach the nylon stem to the Purple-Days Vaporizer

Now place the herb end on top of the Purple-Days. You should see the mouthpiece end pointing straight upwards out of the Purple-Days once you place it on top.

Step 5: Being use of the Purple-Days Vaporizer

Next you’ll want to take the Purple-Days in hand and lift it up and pull from the mouthpiece end of the nylon stem. You should be able to get at least 3 to 4 big hits and then a couple clearing hits from each bowl pack.

If you are looking for a review of the Purple-Days Vaporizer you can find ours here. Interested in buying this vape? Before you do compare prices and vendors for the Purple-Days Vaporizer.

Posted in Articles, How to Use | Tagged , , | Leave a comment

5 Easy Steps on How to Use the Myrtlezap Vaporizer

Myrtlezap 5 Easy Steps on How to Use the Myrtlezap Vaporizer

Step 1: Turn on the Myrtlezap Vaporizer

First you want to plug in the Myrtlezap, simply put the A/C adapter plug in the back of the vape and plug the other end into the wall. The cord for this vape is pretty long and skinnier than most, but definitely not fragile.

Step 2: Heat up the Myrtlezap Vaporizer

You have to give the Myrtlezap about 30 to 45 minutes to heat up the first time, but you can leave it on after that for as long as you like so it isn’t a big concern. Once you’ve heated it for 45 minutes, to be safe, you can fill one of the short nylon stems.

Step 3: Pack the Myrtlezap Vaporizer

Take one of the nylon stems provided and place the herb bowl end over your ground up herb. Now pull the herb into the herb chamber by gently pulling from the mouthpiece end. Once you see it filled with herb take the small packing tool they give you and lightly pack the herb into the chamber. Just don’t push too hard.

Step 4: Attach the nylon stem to the Myrtlezap Vaporizer

Now place the herb end on top of the Myrtlezap. The herb end will fit nicely on the top leaving the mouthpiece end pointing straight upwards.

Step 5: Being use of the Myrtlezap Vaporizer

Next you’ll want to take the Myrtlezap in hand and lift it up and pull from the mouthpiece end of the nylon stem. You should be able to get at least 3 to 4 big hits and then a couple clearing hits from each bowl pack.

If you haven’t yet read our extensive review of the Myrtlezap Vaporizer you can find it here. Want to purchase this vape? Before you do compare prices and vendors for the Myrtlezap Vaporizer.

Posted in Articles, How to Use | Tagged , , | Leave a comment

3 Easy Steps on How to Use the Eclipse Vape2o Vaporizer

Eclipse 3 Easy Steps on How to Use the Eclipse Vape2o Vaporizer

Step 1: Pack the Eclipse Vape2o Vaporizer

First you want to take the glass vial off of the vaporizer. It is threaded so you just twist it off, it should untwist rather easily. Now place your herb into the vial of the Vape2o Vaporizer and screw it back on.

Step 2: Begin use of the Eclipse Vape2o Vaporizer

Now light the lighter and hold it under the glass vial where the herb is resting. I’ve found that holding the flame away from the vial, meaning the flame isn’t actually touching the glass, works best for vaporizing. It might take a little longer but it works better in my opinion. When you see the vial fill with vapor simply pull from the mouthpiece.

Step 3: Refill the Eclipse Vape2o Vaporizer

When the herb looks done or you start to get a burnt taste it is time to unscrew the vial, be careful because it might still be hot, and empty the herb. Now just put new herb in the vial and screw it back on to continue use.

If you haven’t read the review for the Eclipse Vape2o Vaporizer yet you need to get on that, you can find it here. Want to see how much this vaporizer costs? Compare prices and vendors for the Eclipse Vape2o Vaporizer.

Posted in Articles, How to Use | Tagged , | Leave a comment

3 Easy Steps on How to Use the Ape Vape Vaporizer

Ape Vape 3 Easy Steps on How to Use the Ape Vape Vaporizer

Step 1: Pack the Ape Vape Vaporizer

Take your ground up herb and place it in to the bowl piece that fits into your water pipe. Like usual be sure not to over pack your bowl, the Ape Vape can fit more than normal bowls but still be careful so you don’t waste any herb.

Step 2: Heat the Ape Vape Vaporizer

Use the vaporizing computer to set the temperature that you wish to vaporize at. Since it uses the computer it will be able to tell temperature changes in the heater and fix it immediately. This is always going to ensure that you have the same vaporizing experience every time you use the Ape Vape.

Step 3: Begin use of the Ape Vape Vaporizer

Put the heater onto the top of the bowl piece containing the herb. You will see your water pipe fill with vapor and you are now ready to pull from it. A lot of the time it is best to take a couple quick hits first to get the vapor flowing. After a couple quick hits you can start pulling more from it.

Take a look at our in depth review of the Ape Vape Vaporizer before you make any final decisions. Want to see how much this vape costs? Compare prices and vendors for the Ape Vape Vaporizer.

Ape Vape Vaporizer
Posted in Articles, How to Use | Tagged , , | Leave a comment

5 Easy Steps on How to Use the Pure Vaporizer

Pure Vaporizer 5 Easy Steps on How to Use the Pure Vaporizer

Step 1: Turn on the Pure Vaporizer

Turn on the Pure Vaporizer and wait for it to reach it’s set temperature. Usually a little over half way is a good setting to start at.

Step 2: Pack the Pure Vaporizer

Now pack your grounded herb into the bowl piece of the glass wand. Like most vaporizers, the Pure Vaporizer recommends that you only fill the bowl piece about 1/3 of the way so you don’t waste any herb.

Step 3: Attach the vapor whip to the Pure Vaporizer

Now attach the vapor whip to the metal heating element putting the end with the herb packed into it on the heating element.

Step 4: Begin use of the Pure Vaporizer

This begins the vaporization process. Draw as much vapor from it as is comfortable for you and continue throughout the session. The temperature should stay the same throughout to ensure your vaporizing experience doesn’t change.

Step 5: Refill the Pure Vaporizer

Once the herb is kicked, simply take the whip off with another twisting motion and discard the herb. Replace the herb with freshly ground herb and repeat the previous steps.

If you haven’t got a chance to read the Pure Vaporizer review you should do that before making a final decision. If you still aren’t sure the Pure Vaporizer is for you why don’t you compare prices and vendors for it.

Posted in How to Use | Tagged , , | Leave a comment

5 Easy Steps on How to Use the iVape Vaporizer

ivape 5 Easy Steps on How to Use the iVape Vaporizer

Step 1: Turn on the iVape Vaporizer

Turn on the iVape Vaporizer and wait for it to reach it’s set temperature. Usually a little over half way is a good setting to start at.

Step 2: Pack the iVape Vaporizer

Now pack your grounded herb into the bowl piece of the glass wand. Like most vaporizers, the iVape Vaporizer recommends that you only fill the bowl piece about 1/3 of the way so you don’t waste any herb.

Step 3: Attach the vapor whip to the iVape Vaporizer

Now attach the vapor whip to the metal heating element putting the end with the herb packed into it on the heating element.

Step 4: Begin use of the iVape Vaporizer

This begins the vaporization process. Draw as much vapor from it as is comfortable for you and continue throughout the session. The temperature should stay the same throughout to ensure your vaporizing experience doesn’t change.

Step 5: Refill the iVape

Once the herb is kicked, simply take the whip off with another twisting motion and discard the herb. Replace the herb with freshly ground herb and repeat the previous steps.

If you haven’t read the review for the iVape Vaporizer you can find it here. Still not sure the iVape is for you? Compare prices and vendors for the iVape Vaporizer.

Posted in Articles, How to Use | Tagged , , | Leave a comment

3 Easy Steps on How to Use the Vapor Bat by VripTech

vapor bat vrip 3 Easy Steps on How to Use the Vapor Bat by VripTech

Step 1: Pack the Vapor Bat

Insert your ground up herb into the end of the Vapor Bat, make sure it is spread out and finely ground up. It can be a little difficult to accurately pack this vape at times due to how small it is so you might want to take extra care when putting the herb in the slider.

Step 2: Light the Vapor Bat

Put your car lighter to the end of the Vapor Bat and use the intake slider to find which position works best to vaporize at. You will have to experiment a lot to find the right way to vaporize and not burn the herb. You might end up wasting quite a bit of herb getting it right.

Step 3: Begin use of the Vapor Bat

Pull from the Vapor Bat and continue to use the intake slider while you do so you can find out what is going to work best for you to get vapor and not burn the herb. You shouldn’t generate too much vapor at one time because if you do you are increasing the chance of starting to burn the herb. A lot of people make the mistake of trying to take gigantic hits.

Check out our in depth review of the Vapor Bat if you haven’t already. Wondering how much this vaporizer costs? Compare prices and vendors for the Vapor Bat before buying.

Posted in Articles, How to Use | Tagged , , , | Leave a comment
← Older posts
Get the newsletter:

Vaporizer Sale has 82 followers

Copyright © 2011. All Rights Reserved.